检修作业操作牌收还确认表 编号： 日期 收操作 牌时间 收操作 牌部门 收操作牌名称数量 收操作牌 人签名 岗位确 认签名 还操作 牌时间 还操作 牌部门 还操作牌名称数量 还操作牌 者签名 岗位确认 签名 备注 填写要求：1、全厂定检由设备管理部门负责收取、返还相关岗位的操作牌；单线检修由检修员负责收取、返还相关岗位的操作牌；临时故障处理由设备 检修人员负责收取、返还操作牌。 2、由需检修岗位的班组长负责收取、返还操作牌的确认签字工作。检修结束后，岗位操作人员收取操作牌签字后，进行试车前必须到所要启动的设备 周围再次确认具备试车安全条件，方可启动设备运行。 3、日期、收操作牌时间、收操作牌单位、收操作牌名称数量、收取返还岗位确认签名栏由需检修岗位的班组长填写；收操作牌人签名、还操作牌单位、 还操作牌时间、还操作牌者签名栏由专业人员或检修人员填写。
分类：安全操作规程 行业：食品医药行业 文件类型：Word 文件大小：39 KB 时间：2025-08-10 价格：¥2.00
图书馆、机房、实验室、教室安全应急预案 1.火灾事故应急预案 2.被盗案件应急预案 3.大型活动突发事件处置应急预案 4.停电应急预案 5.楼道拥挤发生踩踏事故应急预案 6. 触电事故应急预案 （一）、火灾事故应急预案 1、处置火灾事故的组织：机房、图书馆、实验室、教室相关负责领导， 值日教师，校消防安全员。 2、报告程序： （1）机房、图书馆、实验室、教室值班老师。（2）机房、图书馆、 实验室、教室相关负责领导。（3）学校相关负责领导、（4）上级公 安消防部门。 3、报警程序： ⑴迅速组织有关人员携带消防器具赶赴现场进行扑救。 ⑵根据火势如需报警立即就近用电话或手机报告消防中心（电话 119），报告内容为：发生火灾，请迅速前来扑救”，待对方放下电 话后再挂机。 ⑶在向机房、图书馆、实验室、教室、校相关负责领导汇报的同时， 派出专门人员到显眼位置或主要路口等待引导消防车辆进入现场。 4、组织实施： ⑴参加人员：在消防车到来之前，以馆区内消防安全员和职工成员为 主，其余人员（学生除外）均有义务参加扑救。
分类：事故与应急 行业：其它行业 文件类型：Word 文件大小：36 KB 时间：2025-08-17 价格：¥2.00
ICS 03 A 00 DB37 山东省地方标准 DB37/T 2882—2016 安全生产风险分级管控体系通则 General rules for the management and control system of work safety risk classification 2016-12-07 发布 2017-01-08 实施 山东省质量技术监督局 发 布 DB37/T 2882—2016 I 目 次 前言.................................................................................III 引言..................................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................2 5 总体结构............................................................................3 5.1 标准层级........................................................................3 5.2 安全生产风险分级管控体系通则....................................................3 5.3 安全生产风险分级管控体系细则....................................................3 5.4 安全生产风险分级管控实施指南....................................................3 6 工作程序和内容......................................................................4 6.1 风险判定准则....................................................................4 6.2 风险点确定......................................................................4 6.2.1 风险点划分原则..............................................................4 6.2.1.1 设施、部位、场所、区域..................................................4 6.2.1.2 操作及作业活动..........................................................4 6.2.2 风险点排查..................................................................4 6.2.2.1 风险点排查的内容........................................................4 6.2.2.2 风险点排查的方法........................................................4 6.3 危险源辨识......................................................................4 6.3.1 危险源辨识的内容............................................................4 6.3.2 危险源辨识的方法............................................................4 6.4 风险评价........................................................................4 6.4.1 评价方法....................................................................4 6.4.2 重大风险确定原则............................................................5 6.4.3 风险点级别确定..............................................................5 6.5 风险控制措施....................................................................5 6.5.1 风险控制措施类别............................................................5 6.5.2 风险控制措施确定的要求......................................................5 6.5.2.1 基本原则................................................................5 6.5.2.2 评审....................................................................5 6.5.3 重大风险控制措施............................................................5 6.6 风险分级管控....................................................................6 6.6.1 风险分级....................................................................6
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：824 KB 时间：2025-11-19 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 光气及光气化企业 安全生产风险分级管控体系 实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of Companies Which Possess Phosgene or Conduct Phosgenation 文稿版次选择 XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX I 目 次 前 言.............................................................................III 引 言..............................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................1 4.1 成立组织机构....................................................................1 4.2 实施全员培训....................................................................1 4.3 编写体系文件....................................................................1 5 工作程序和内容......................................................................1 5.1 风险点确定......................................................................1 5.1.1 风险点划分原则..............................................................2 5.1.2 风险点排查..................................................................2 5.2 危险源辨识......................................................................2 5.2.1 辨识方法....................................................................2 5.2.2 辨识范围....................................................................2 5.2.3 危险源辨识..................................................................3 5.3 风险评价........................................................................3 5.3.1 风险评价方法................................................................3 5.3.2 风险评价准则................................................................3 5.3.3 风险评价与分级..............................................................3 5.3.4 确定重大风险................................................................4 5.3.5 风险点级别确定..............................................................4 5.4 风险控制措施....................................................................4 5.5 风险分级管控....................................................................4 5.5.1 风险分级管控的要求..........................................................5 5.5.2 编制风险分级管控清单........................................................5 5.5.3 风险告知....................................................................5 6 文件管理............................................................................5 7 分级管控的效果......................................................................5 8 持续改进............................................................................6 8.1 评审............................................................................6 8.2 更新............................................................................6 8.3 沟通............................................................................6
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：591 KB 时间：2025-11-21 价格：¥2.00
I DB 37/ XXXXX—XXXX 复合肥制造行业企业生产安全事故隐患 排查治理体系实施指南 Detailed rule for the system of screening for and elimination of industry commerce and trade hidden risks of ×× XXXX - XX - XX 发布 XXXX - XX - XX 实施 山东省质量技术监督局 发 布 ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB37/ XXXXX—XXXX 1 目 录 前 言......................................................................2 引 言......................................................................3 复合肥制造行业企业生产安全事故隐患排查治理体系细则..........................4 1 范围......................................................................4 2 规范性引用文件............................................................5 3 术语与定义................................................................5 4 基本要求..................................................................5 4.1 全员落实 ................................................................5 4.2 安全管理一体化 ..........................................................6 4.3 完善制度，激励约束 ......................................................6 5 隐患分级与分类............................................................6 6 工作程序和内容............................................................7 6.1 编制排查项目清单 ........................................................7 6.1.1 基本要求 ............................................................7 6.1.2 生产现场类隐患排查项目清单 ..........................................7 6.1.3 基础管理类隐患排查项目清单 ..........................................7 6.2 隐患排查 ................................................................7 6.2.1 排查类型 ............................................................7 6.2.2 排查要求 ............................................................8 6.2.3 组织级别 ............................................................8 6.2.4 排查周期 ............................................................8 6.2.5 确定排查项目 ........................................................9 6.2.6 排查结果记录 ........................................................9 6.3 隐患治理 ................................................................9 6.3.1 隐患治理建议 ........................................................9 6.3.2 隐患治理要求 ........................................................9 6.3.3 隐患治理流程 ........................................................9 6.3.4 一般隐患治理 ........................................................9 6.3.5 重大隐患治理 .......................................................10 7 文件管理.................................................................10 8 隐患排查治理效果.........................................................11 9 持续改进.................................................................11 10 附件： ..................................................................11
分类：安全管理制度 行业：建筑加工行业 文件类型：Word 文件大小：269 KB 时间：2025-11-22 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 空气分离行业企业 安全生产风险分级管控体系实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of XX XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX I 目 次 前 言.............................................................................III 引 言..............................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................1 4.1 成立组织机构....................................................................1 4.2 实施全员培训....................................................................2 4.3 编写体系文件....................................................................2 5 工作程序和内容......................................................................2 5.1 风险点确定......................................................................3 5.1.1 风险点划分原则..............................................................3 5.1.2 风险点排查..................................................................3 5.2 危险源辨识......................................................................4 5.2.1 辨识方法....................................................................4 5.2.2 辨识范围....................................................................4 5.2.3 危险源辨识..................................................................4 5.2.4 评审与审批..................................................................4 5.3 风险评价........................................................................4 5.3.1 风险评价方法................................................................4 5.3.2 风险评价准则................................................................5 5.3.3 风险评价与分级..............................................................5 5.3.4 确定重大风险................................................................5 5.3.5 风险点级别确定..............................................................5 5.4 风险控制措施....................................................................6 5.4.1 控制措施的选择原则..........................................................6 5.4.2 控制措施实施................................................................6 5.5 风险分级管控....................................................................7 5.5.1 风险分级管控的要求..........................................................7 5.5.2 编制风险分级管控清单........................................................7 5.5.3 评审与审批..................................................................7 5.5.4 风险告知....................................................................7 6 文件管理............................................................................8 7 分级管控的效果......................................................................8 8 持续改进............................................................................9
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：1.06 MB 时间：2025-11-25 价格：¥2.00
山东省地下开采硬质粘土矿山安全生产风险分级管控体系实施指南 1 山东省地下开采硬质粘土矿山 安全生产风险分级管控体系 实施指南 山东省地下开采硬质粘土矿山安全生产风险分级管控体系实施指南 2 目 录 前 言 ............................................................................................................................................1 引 言 ............................................................................................................................................2 1 范围..............................................................................................................................................3 2 规范性引用文件 ..........................................................................................................................3 3.术语和定义 ..................................................................................................................................3 3.1 ....................................................................................................................................3 4 基本要求 .......................................................................................................................................4 4.1 成立组织机构.............................................................................................................4 4.1.1 主要负责人职责 ....................................................................................................4 4.1.2 分管安全负责人（安全总监）职责 ......................................................................4 4.1.3 其他分管负责人职责.............................................................................................4 4.1.4 安全生产管理机构负责人职责..............................................................................4 4.1.5 安全生产管理人员的职责 ......................................................................................4 4.1.6 相关职能部门、职能层级的职责...........................................................................5 4.2 实施全员培训............................................................................................................5 4.3 编写体系文件............................................................................................................5 5 工作程序和内容 ...........................................................................................................................5 5.1 风险点确定................................................................................................................5 5.1.1 风险点划分原则 ......................................................................................................5 5.1.2 风险点排查..............................................................................................................5 5.2 危险源辨识................................................................................................................6 5.2.1 辨识方法 ..................................................................................................................6 5.2.2 辨识范围 .................................................................................................................6 5.2.3 危险源辨识..............................................................................................................7 5.3 风险评价 ...................................................................................................................7 5.3.1 风险评价方法..........................................................................................................7 5.3.2 风险评价准则..........................................................................................................7 5.3.3 风险评价与分级 ......................................................................................................8 5.3.4 确定重大风险..........................................................................................................8 5.3.5 风险点级别确定 .......................................................................................................8 5.4 风险管控措施............................................................................................................8 5.4.1 控制措施的选择原则................................................................................................8 5.4.2 控制措施实施...........................................................................................................8 5.5 风险分级管控............................................................................................................9 5.5.1 风险分级管控的要求................................................................................................9 5.5.2 编制风险分级管控清单...........................................................................................9 5.5.3 风险告知 .................................................................................................................9 6 文件管理 .......................................................................................................................................9 7 分级管控的效果 ...........................................................................................................................9 8 持续改进 ....................................................................................................................................10
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：1.75 MB 时间：2025-11-28 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 合成树脂行业安全生产风险分级 管控体系实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of synthetic resin 文稿版次选择 XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX 1 目 次 目 次……………………………………………………………………………………………………..I 前 言.............................................................................III 引 言..............................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................1 4.1 成立组织机构....................................................................5 4.2 实施全员培训....................................................................7 4.3 编写体系文件....................................................................8 5 风险识别评价.......................................................................10 5.1 风险点确定.....................................................................10 5.1.1 风险点划分原则.............................................................10 5.1.2 风险点排查.................................................................10 5.2 危险源辨识分析.................................................................11 5.2.1 危险源辨识.................................................................11 5.2.2 危险源辨识范围.............................................................11 5.2.3 危险源辨识实施.............................................................11 5.3 风险控制措施...................................................................12 5.4 风险评价……………………………………………………………………………………………….12 5.4.1 风险评价方法.................................................................12 5.4.2 风险评价准则 ..................................................................12 5.5 风险分级管控………………………………………………………………………………………….12 5.5.1 管控原则...................................................................12 5.5.2 重大风险判定……………………………………………………………………………………. 13 5.5.3 风险分级管控实施……………………………………………………………………………….13 5.5.4 编制风险分级管控清单 ........................................................13 6 成果与运用.........................................................................13 6.1 档案记录…………………………………………………………………………………………………13 6.2 风险信息记录……………………………………………………………………………………………13 7 分级管控的效果.....................................................................13 8 持续改进...........................................................................13 8.1 评审...........................................................................14 8.2 更新...........................................................................14
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：2.26 MB 时间：2025-11-28 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 甲醛生产行业企业安全生产 风险分级管控体系实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of XX XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX I 前 言................................................................................Ⅱ 引 言................................................................................Ⅲ 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................1 4.1 成立组织机构....................................................................2 4.2 实施全员培训....................................................................2 4.3 编写体系文件....................................................................2 5 工作程序和内容......................................................................2 5.1 风险点确定......................................................................2 5.1.1 风险点划分原则..............................................................2 5.1.2 风险点排查..................................................................3 5.2 危险源辨识......................................................................3 5.2.1 辨识方法....................................................................3 5.2.2 辨识范围....................................................................3 5.2.3 危险源辨识..................................................................4 5.3 风险评价........................................................................4 5.3.1 风险评价方法................................................................4 5.3.2 风险评价准则................................................................4 5.3.3 风险评价与分级..............................................................4 5.3.4 确定重大风险................................................................5 5.3.5 风险点级别确定..............................................................5 5.4 风险控制措施....................................................................6 5.5 风险分级管控....................................................................6 5.5.1 风险分级管控的要求..........................................................6 5.5.2 编制风险分级管控清单........................................................6 5.5.3 风险告知....................................................................6 6 文件管理............................................................................7 7 分级管控的效果......................................................................7 8 持续改进............................................................................7 8.1 评审............................................................................7 8.2 更新............................................................................7 8.3 沟通............................................................................7 附录 A：甲醛生产行业企业风险分析记录（资料性附录） 风险分析记录
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：818 KB 时间：2025-11-29 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 甲烷氯化物行业企业安全生产风险分级管 控体系实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of XX XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX I 目 次 前 言.............................................................................III 引 言..............................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................1 4.1 成立组织机构....................................................................1 4.2 实施全员培训....................................................................1 4.3 编写体系文件....................................................................1 5 工作程序和内容......................................................................1 5.1 风险点确定......................................................................1 5.1.1 风险点划分原则..............................................................2 5.1.2 风险点排查..................................................................2 5.2 危险源辨识......................................................................2 5.2.1 辨识方法....................................................................2 5.2.2 辨识范围....................................................................2 5.2.3 危险源辨识..................................................................3 5.3 风险评价........................................................................3 5.3.1 风险评价方法................................................................3 5.3.2 风险评价准则................................................................3 5.3.3 风险评价与分级..............................................................3 5.3.4 确定重大风险................................................................4 5.3.5 风险点级别确定..............................................................4 5.4 风险控制措施....................................................................4 5.5 风险分级管控....................................................................4 5.5.1 风险分级管控的要求..........................................................5 5.5.2 编制风险分级管控清单........................................................5 5.5.3 风险告知....................................................................5 6 文件管理............................................................................5 7 分级管控的效果......................................................................5 8 持续改进............................................................................6 8.1 评审............................................................................6 8.2 更新............................................................................6 8.3 沟通............................................................................6
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：1.06 MB 时间：2025-11-30 价格：¥2.00
ICS 03 A 00 DBXX 山东省地方标准 DB XX/ XXXXX—XXXX 乳制品企业生产安全事故隐患排查治理体 系建设实施指南 点击此处添加标准英文译名 点击此处添加与国际标准一致性程度的标识 文稿版次选择 XXXX - XX - XX 发布 XXXX - XX - XX 实施 山东省质量技术监督局 发 布 DBXX/ XXXXX—XXXX I 目 次 前言.................................................................................III 引言..................................................................................IV 1 范围.................................................................................5 2 规范性引用文件.......................................................................5 3 术语和定义...........................................................................5 4 基本要求.............................................................................5 4.1 全员落实.........................................................................5 4.2 安全管理一体化...................................................................5 4.3 激励约束.........................................................................5 4.4 完善制度.........................................................................5 5 隐患分级与分类.......................................................................6 5.1 分级.............................................................................6 5.1.1 一般事故隐患.................................................................6 5.1.2 重大事故隐患.................................................................6 5.2 分类.............................................................................6 5.2.1 基础管理类隐患...............................................................6 5.2.2 生产现场类隐患...............................................................6 6 工作程序和内容.......................................................................6 6.1 编制排查项目清单.................................................................6 6.2 制定排查计划 .....................................................................7 6.3 隐患排查.........................................................................7 6.3.1 排查类型.....................................................................7 6.3.2 排查要求.....................................................................7 6.3.3 组织级别.....................................................................7 6.3.4 排查周期.....................................................................8 6.3.5 确定排查项目.................................................................8 6.3.6 排查结果记录................................................................8 6.4 隐患治理…………………………………………………………………………………………………8 6.4.1 隐患治理建议.................................................................8 6.4.2 隐患治理要求.................................................................9 6.4.3 隐患治理流程.................................................................9 6.4.4 一般隐患治理.................................................................9 6.4.5 重大隐患治理.................................................................9 6.4.6 隐患治理验收................................................................10 6.4.7 隐患数据分析................................................................10 7 文件管理............................................................................10 8 隐患排查的效果......................................................................10
分类：安全管理制度 行业：建筑加工行业 文件类型：Word 文件大小：75.8 KB 时间：2025-11-30 价格：¥2.00
炊事机械日常点检表 点检月份： 年 月 编号： 设备名称 炊事机械 规格型号 设备编号 操作者 A 操作者 B 操作者 C 使用部门 检查日期 点检内容 点检记录 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 机械传动部位有完好可靠的防护装置 2 搅拌操作的容器必须加盖密闭且盖机联锁 3 PE 连接可靠，电源线路完好 4 每台设备应有单独的控制开关 5 凡有碾绞压挤切伤可能的部位均应有可靠防护 1 8 15 2 9 16 3 10 17 4 11 18 5 12 19 6 13 20 异 常 情 况 记 录 7 14 21 备 注 1.检查方法：看、听、试 2.检查周期：每天。（由车间负责人负责） 重大 安全 隐患 记录 注：保养后，用“√”表示进行了点检，“○”表示休息或放假， “×”表示有异常情况，应在“异常情况记录”栏予以记录。
分类：安全管理制度 行业：其它行业 文件类型：Word 文件大小：70 KB 时间：2025-11-30 价格：¥2.00
ICS 点击此处添加中国标准文献分类号 DB 山东省地方标准 DB XX/ —XXXX 黄金采选企业职业病危害风险分级管控体 系建设实施指南 Implementary guide for management and control system of occupational disease hazards risk classification of Gold Mining Enterprises 点击此处添加与国际标准一致性程度的标识 （工作组讨论稿） XXXX - XX - XX 发布 XXXX - XX - XX 实施 山东省质量技术监督管理局 发 布 DBXX/ —XXXX I 目 次 目 次................................................................................I 前 言...............................................................................II 引 言..............................................................................III 1 范围..................................................................................1 2 规范性引用文件........................................................................1 3 术语和定义............................................................................1 4 职责要求..............................................................................2 5 工作程序和内容........................................................................3 5.1 职业危害识别与分析................................................................3 5.2 职业病危害风险点确定..............................................................5 5.3 职业病危害风险评价................................................................5 5.4 职业病危害风险控制措施............................................................6 5.5 职业病危害风险告知................................................................6 6 文件管理和持续改进....................................................................6 6.1 文件管理..........................................................................6 6.2 持续改进..........................................................................6 附 录 A （资料性附录） 黄金采选企业主要工艺流程示意图................................7 附 录 B （资料性附录） 黄金采选企业职业病危害风险清单................................8 附 录 C （资料性附录） 黄金采选企业职业病危害风险管控措施...........................15 附 录 D （规范性附录） 黄金采选企业职业病危害重大风险应急处置措施...................47 附 录 E （资料性附录） 黄金采选企业职业病危害风险告知卡举例.........................50
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：551 KB 时间：2025-12-01 价格：¥2.00
ICS 03 A 00 DB37 山东省地方标准 DB XX/ XXXXX—XXXX 冶金行业企业生产安全事故隐患排查治理 体系实施指南 Detailed rule for the system of screening for and elimination of industry commerce and trade hidden risks of work safety accidents 点击此处添加与国际标准一致性程度的标识 文稿版次选择 图1 XXXX-XX-XX 发布 XXXX-XX- 山东省质量技术监督局 发 布 1 DBXX/ XXXXX—XXXX I 目 次 前言.................................................................................III 引言..................................................................................IV 1 范围.................................................................................5 2 规范性引用文件.......................................................................5 3 术语和定义...........................................................................5 4 总则.................................................................................5 4.1 任务目标.........................................................................5 4.2 基本要求.........................................................................5 5 隐患分级与分类.......................................................................6 5.1 分级.............................................................................6 5.1.1 一般事故隐患.................................................................6 5.1.2 重大事故隐患.................................................................6 5.2 分类.............................................................................6 5.2.1 基础管理类隐患...............................................................6 5.2.2 生产现场类隐患...............................................................6 6 工作程序和内容.......................................................................6 6.1 编制排查项目清单.................................................................6 6.2 隐患排查.........................................................................7 6.2.1 排查类型.....................................................................7 6.2.2 排查要求.....................................................................7 6.2.3 组织级别.....................................................................7 6.2.4 排查周期.....................................................................8 6.2.5 制定排查计划.................................................................8 6.2.6 确定排查项目.................................................................8 6.3 隐患治理.........................................................................8 6.3.1 隐患治理建议.................................................................8 6.3.2 隐患治理要求.................................................................9 6.3.3 隐患治理流程.................................................................9 6.3.4 一般隐患治理.................................................................9 6.3.5 重大隐患治理.................................................................9 6.3.6 隐患治理验收................................................................10 7 文件管理............................................................................10 8 隐患排查的效果......................................................................10 9 持续改进............................................................................10 9.1 评审............................................................................10 9.2 更新............................................................................10 9.3 沟通............................................................................11
分类：安全管理制度 行业：建筑加工行业 文件类型：Word 文件大小：67.5 KB 时间：2025-12-03 价格：¥2.00
I ICS 点击此处添加中国标准文献分类号 DB 山东省地方标准 DB XX/ XXXXX—XXXX 黄金采选企业职业病隐患排查治理 体系建设实施指南 Implementary guide for screening and elimination of occupational disease hidden risk of gold mining enterprises 点击此处添加与国际标准一致性程度的标识 文稿版次选择 XXXX - XX - XX 发布 XXXX - XX - XX 实施 山东省质量技术监督管理局 发 布 DBXX/ XXXXX—XXXX II 目 次 目 次...............................................................................I 前 言.............................................................................III 引 言................................................................................I 1 范围.................................................................................1 2 规范性引用文件.......................................................................1 3 术语、 定义.........................................................................1 4 职责要求.............................................................................2 4.1 职责.............................................................................2 4.2 基本要求.........................................................................2 5 职业病隐患分类和分级.................................................................3 5.1 职业病隐患分类...................................................................3 5.2 职业病隐患分级...................................................................3 6 工作程序和内容.......................................................................4 6.1 职业病隐患排查项目清单...........................................................4 6.2 职业病隐患排查...................................................................4 6.3 职业病隐患评估...................................................................5 6.4 职业病隐患治理...................................................................5 7 持续改进和文件管理...................................................................7 7.1 职业病隐患治理项目验收...........................................................7 7.2 触发进行职业病危害隐患排查的情形.................................................7 7.3 文件管理.........................................................................7 7.4 信息交流与公告警示...............................................................7 附 录 A （资料性附录） 现场管理类隐患排查治理清单（举例）............................8 附 录 B （资料性附录） 现场管理类隐患排查治理台账...................................57 附 录 C （资料性附录） 基础管理类隐患排查治理清单（举例）...........................58 附 录 D （资料性附录） 基础管理类隐患排查治理台账...................................66
分类：安全管理制度 行业：建筑加工行业 文件类型：Word 文件大小：720 KB 时间：2025-12-03 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 橡胶防老剂行业企业生产安全风险分级管 控体系实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of Rubber antioxidant 文稿版次选择 XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX I 目 次 前 言...............................................................................III 引 言................................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................1 4.1 成立组织机构....................................................................1 4.2 实施全员培训....................................................................1 4.3 编写体系文件....................................................................1 5 工作程序和内容......................................................................1 5.1 风险点确定......................................................................1 5.1.1 风险点划分原则..............................................................2 5.1.2 风险点排查..................................................................2 5.2 危险源辨识......................................................................2 5.2.1 辨识方法....................................................................2 5.2.2 辨识范围....................................................................2 5.2.3 危险源辨识..................................................................3 5.3 风险评价........................................................................3 5.3.1 风险评价方法................................................................3 5.3.2 风险评价准则................................................................3 5.3.3 风险评价与分级..............................................................3 5.3.4 确定重大风险................................................................4 5.3.5 风险点级别确定..............................................................4 5.4 风险控制措施....................................................................4 5.5 风险分级管控....................................................................4 5.5.1 风险分级管控的要求..........................................................5 5.5.2 编制风险分级管控清单........................................................5 5.5.3 风险告知....................................................................5 6 文件管理............................................................................5 7 分级管控的效果......................................................................5 8 持续改进............................................................................6 8.1 评审............................................................................6 8.2 更新............................................................................6 8.3 沟通............................................................................6
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：2 MB 时间：2025-12-04 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 葡萄酒制造行业企业安全生产 风险分级管控体系实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of Wine manufacturing industry enterprise 文稿版次选择 XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX I 目 次 前 言...............................................................................III 引 言................................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................1 4.1 成立组织机构....................................................................1 4.2 实施全员培训....................................................................1 4.3 编写体系文件....................................................................1 5 工作程序和内容......................................................................1 5.1 风险点确定......................................................................1 5.1.1 风险点划分原则..............................................................2 5.1.2 风险点排查..................................................................2 5.2 危险源辨识......................................................................2 5.2.1 辨识方法....................................................................2 5.2.2 辨识范围....................................................................2 5.2.3 危险源辨识..................................................................3 5.3 风险评价........................................................................3 5.3.1 风险评价方法................................................................3 5.3.2 风险评价准则................................................................3 5.3.3 风险评价与分级..............................................................3 5.3.4 确定重大风险................................................................4 5.3.5 风险点级别确定..............................................................4 5.4 风险控制措施....................................................................4 5.5 风险分级管控....................................................................4 5.5.1 风险分级管控的要求..........................................................5 5.5.2 编制风险分级管控清单........................................................5 5.5.3 风险告知....................................................................5 6 文件管理............................................................................5 7 分级管控的效果......................................................................5 8 持续改进............................................................................6 8.1 评审............................................................................6 8.2 更新............................................................................6 8.3 沟通............................................................................6
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：64.6 KB 时间：2025-12-06 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 汽车铝合金车轮制造行业企业 安全生产风险分级管控体系实施指南 Detailed rule for the system of screening for and elimination of industry commerce and trade hidden risks of work safety accidents 点击此处添加与国际标准一致性程度的标识 文稿版次选择 2017-5-XX 发布 2017-6-XX 实施 山东省质量技术监督局 发 布 DB37/ XXXXX—XXXX I 目 次 前 言................................................................................II 引 言...............................................................................III 1 范围.................................................................................1 2 规范性引用文件.......................................................................1 3 术语和定义...........................................................................1 4 基本要求.............................................................................1 4.1 成立组织机构.....................................................................1 4.2 实施全员培训.....................................................................2 4.3 编写体系文件.....................................................................3 5 工作程序和内容.......................................................................3 5.1 风险点确定.......................................................................3 5.2 危险源辨识.......................................................................4 5.3 风险评价.........................................................................7 5.4 风险控制措施的制定与实施.........................................................8 5.5 风险分级管控.....................................................................9 6 文件管理.............................................................................9 7 分级管控的效果.......................................................................9 8 持续改进.............................................................................9 8.1 评审............................................................................10 8.2 更新............................................................................10 8.3 沟通............................................................................10 附 录 A 风险评价方法................................................................11 附 录 B 作业活动清单................................................................13 附 录 C 设备设施清单................................................................13 附 录 D 工作危害分析（JHA）评价记录.................................................13 附 录 E 安全检查表分析（SCL）评价记录...............................................13 附 录 F 作业活动风险分级管控清单....................................................13 附 录 G 设备设施风险分级管控清单....................................................13 附 录 H 风险告知卡..................................................................13 附 录 I 参考文献....................................................................13
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：85.8 KB 时间：2025-12-11 价格：¥2.00
ICS H 备案号： 中华人民共和国安全生产行业标准 AQ 2023－2008 耐火材料生产安全规程 Safety regulations for refractory material （ 送 审 稿 ） 2008-11-19 发布 2009-01-01 实施 国家安全生产监督管理总局 发布 AQ2023－2008 目 次 前 言 ······························································································································································II 1 范围 ·······························································································································································1 2 规范性引用文件············································································································································1 3 术语和定义 ···················································································································································1 4 总则 ·······························································································································································2 5 基本规定 ·······················································································································································3 6 厂址选择、厂区布置及厂房 ························································································································4 6.1 厂址选择·············································································································································4 6.2 厂区布置·············································································································································5 6.3 厂房及其内部建、构筑物 ·················································································································5 7 生产工艺 ·······················································································································································6 7.1 原料 ····················································································································································6 7.2 原料煅烧·············································································································································6 7.3 破碎、粉碎、磨碎及筛分 ·················································································································7 7.4 配料、混合·········································································································································7 7.5 成型 ····················································································································································7 7.6 干燥、烧成·········································································································································7 7.7 成品加工·············································································································································9 7.8 纤维制品·············································································································································9 7.9 电熔制品·············································································································································9 7.10 浸渍···················································································································································9 7.11 起重与运输·······································································································································9 7.12 化验、检验·····································································································································11 8 动力供应与管线··········································································································································11 8.1 供电与电气设备·······························································································································11 8.2 动力管线···········································································································································12 9 工业卫生 ·····················································································································································13 9.1 管理和检测········································································································································13 9.2 健康监护···········································································································································14
分类：安全操作规程 行业：其它行业 文件类型：未知 文件大小：210 KB 时间：2025-12-18 价格：¥2.00
ICS75.160.10 D21 备案号：1059－××× 中 华 人 民 共 和 国 煤 炭 行 业 标 准 MT MT/T 739－200× 代替MT/T 739－1997 煤炭堆密度小容器测定方法 Determination of bulk density of coal by small container （ISO 567:1995, Coke-Determination of bulk density in a small container, MOD） （报批稿） 200×－××－××发布 200×－××－××实施 发布 中 华 人 民 共 和 国 国家安全生产监督管理总局 MT/T 739－200× I 目 次 前言.......................................................................................................................................................................II 1 范围....................................................................................................................................................................1 2 规范性引用文件................................................................................................................................................1 3 术语和定义........................................................................................................................................................1 4 方法提要............................................................................................................................................................1 5 仪器设备............................................................................................................................................................1 6 测定步骤............................................................................................................................................................2 7 结果计算与表述................................................................................................................................................2 8 方法精密度........................................................................................................................................................2 9 试验报告内容....................................................................................................................................................2 附 录 A（资料性附录）本标准章条编号与 ISO 1013:1995 章条编号对照..............................................3 附 录 B（资料性附录）本标准 ISO 1013:1995 技术性差异及其原因......................................................4
分类：安全管理制度 行业：其它行业 文件类型：Word 文件大小：103 KB 时间：2025-12-21 价格：¥2.00
ICS 03 A 00 DB37 山东省地方标准 DB37/T 2882—2016 安全生产风险分级管控体系通则 General rules for the management and control system of work safety risk classification 2016-12-07 发布 2017-01-08 实施 山东省质量技术监督局 发 布 DB37/T 2882—2016 I 目 次 前言.................................................................................III 引言..................................................................................IV 1 范围................................................................................1 2 规范性引用文件......................................................................1 3 术语和定义..........................................................................1 4 基本要求............................................................................2 5 总体结构............................................................................3 5.1 标准层级........................................................................3 5.2 安全生产风险分级管控体系通则....................................................3 5.3 安全生产风险分级管控体系细则....................................................3 5.4 安全生产风险分级管控实施指南....................................................3 6 工作程序和内容......................................................................4 6.1 风险判定准则....................................................................4 6.2 风险点确定......................................................................4 6.2.1 风险点划分原则..............................................................4 6.2.1.1 设施、部位、场所、区域..................................................4 6.2.1.2 操作及作业活动..........................................................4 6.2.2 风险点排查..................................................................4 6.2.2.1 风险点排查的内容........................................................4 6.2.2.2 风险点排查的方法........................................................4 6.3 危险源辨识......................................................................4 6.3.1 危险源辨识的内容............................................................4 6.3.2 危险源辨识的方法............................................................4 6.4 风险评价........................................................................4 6.4.1 评价方法....................................................................4 6.4.2 重大风险确定原则............................................................5 6.4.3 风险点级别确定..............................................................5 6.5 风险控制措施....................................................................5 6.5.1 风险控制措施类别............................................................5 6.5.2 风险控制措施确定的要求......................................................5 6.5.2.1 基本原则................................................................5 6.5.2.2 评审....................................................................5 6.5.3 重大风险控制措施............................................................5 6.6 风险分级管控....................................................................6 6.6.1 风险分级....................................................................6
分类：风险评估 行业：其它行业 文件类型：Word 文件大小：824 KB 时间：2025-12-22 价格：¥2.00
目 录 前 言........................................................................................................... ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 家用纺织行业企业安全生产风险分级管控 体系 实施指南 Implementation Guidelines for the Management and Control System of Risk Classification for Production Safety of XX 文稿版次选择 XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 引 言..........................................................................................................................................- 5 - 1.范围..........................................................................................................................................- 6 - 2.规范性引用文件......................................................................................................................- 6 - 3.术语和定义..............................................................................................................................- 6 - 3.1 棉纺、织造、染整等纺织企业 ...................................................................................- 6 - 4.基本要求..................................................................................................................................- 6 - 4.1 成立组织机构 ...............................................................................................................- 6 - 4.2 编写体系文件 ..............................................................................................................- 7 - 4.3 实施全员培训 ...............................................................................................................- 7 - 5.工作程序及要求......................................................................................................................- 8 - 5.1 风险点确定...................................................................................................................- 8 - 5.1.1 风险点划分原则 ...............................................................................................- 8 - 5.1.2 风险点排查和类型 ...........................................................................................- 9 - 5.2 危险源辨识...................................................................................................................- 9 - 5.2.1 危险源的辨识方法 ...........................................................................................- 9 - 5.2.2 危险源的辨识范围 ..........................................................................................- 9 - 5.2.3 危险源的辨识 ..................................................................................................- 9 - 5.3 风险评价.....................................................................................................................- 10 - 5.3.1 风险评价方法 .................................................................................................- 10 - 5.3.2 风险评价准则 .................................................................................................- 10 - 5.3.3 风险评价与分级 ............................................................................................- 10 - 5.3.4 确定重大风险 .................................................................................................- 11 - 5.3.5 风险点级别确定 .............................................................................................- 11 - 5.4 风险控制措施 .............................................................................................................- 11 - 5.4.1 控制措施的选择原则 ....................................................................................- 11 - 5.4.2 控制措施的实施 ............................................................................................- 12 - 5.5 风险分级管控 .............................................................................................................- 12 - 5.5.1 风险分级管控的要求 ....................................................................................- 12 - 5.5.2 编制风险分级管控清单 ................................................................................- 13 - 5.5.3 风险告知 .........................................................................................................- 13 - 6.文件管理................................................................................................................................- 13 - 7.分级管控的效果....................................................................................................................- 14 - 8. 持续改进..............................................................................................................................- 14 - 附录：........................................................................................................................................- 15 -
分类：风险评估 行业：建筑加工行业 文件类型：Word 文件大小：89.9 KB 时间：2025-12-24 价格：¥2.00
ICS 点击此处添加 ICS 号 点击此处添加中国标准文献分类号 DB37 山东省地方标准 DB 37/ XXXXX—XXXX 涂料生产行业企业安全生产事故隐患排查 治理体系体系实施指南 Detailed rule for the system of screening for and elimination of industry commerce and trade hidden risks of work safety accidents 文稿版次选择 XXXX-XX-XX 发布 XXXX-XX-XX 实施 山东省质量技术监督局 发 布 I 目 次 目次...................................................................................I 前言..................................................................................II 引言.................................................................................III 涂料生产行业企业安全生产事故隐患排查治理体系实施指南...................................4 1 范围 .................................................................................4 2 规范性引用文件 .......................................................................4 3 术语和定义 ...........................................................................4 4 基本要求 .............................................................................4 4.1 全员落实...........................................................................4 4.2 安全管理一体化.....................................................................5 4.3 激励约束...........................................................................6 4.4 完善制度...........................................................................6 5 隐患分级与分类 .......................................................................6 5.1 隐患分级 ...........................................................................6 5.2 隐患分类 ...........................................................................6 6 工作程序和内容 .......................................................................6 6.1 编制排查项目清单 ...................................................................6 6.2 制定排查计划（实例） ...............................................................7 6.3 隐患排查 ...........................................................................7 6.4 隐患治理 ...........................................................................8 7 文件管理 ............................................................................10 8 隐患排查治理效果....................................................................10 9 持续改进............................................................................11 9.1 评审..............................................................................11 9.2 更新..............................................................................11 9.3 沟通..............................................................................11 附录 A：基础管理类隐患排查清单 ........................................................12 附录 B：基础管理类隐患排查台账 ........................................................15 附录 C：现场类隐患排查治理清单 ........................................................18 附录 D：现场类隐患排查治理台账 ........................................................73
分类：安全管理制度 行业：建筑加工行业 文件类型：Word 文件大小：531 KB 时间：2026-01-05 价格：¥2.00
I MT/T ××××—20×× 国家安全生产监督管理总局 发 布 中华人民共和国煤炭行业标准 煤矿床水文地质勘查工程质量标准 Quality Standard of Hydrogeological Exploration Projects for Coal Deposit （报批稿） 2010-XX-XX 发布 2010-XX-XX 实施 ICS 73.040 D 20 备案号：×××—×××× I 目 次 前言 …………………………………………………………………………………………………………Ⅱ 1 范围…………………………………………………………………………………………………………1 2 规范性引用文件……………………………………………………………………………………………1 3 术语…………………………………………………………………………………………………………1 4 水文地质钻探工程质量标准………………………………………………………………………………3 5 水文地质测井质量标准……………………………………………………………………………………4 6 抽（放）水试验质量标准…………………………………………………………………………………6 7 水文地质物探质量标准……………………………………………………………………………………8 8 水文地质测绘质量标准…………………………………………………… ……………………………11 9 动态观测质量标准……………………………………………………………… ………………………13 附录 A（资料性附录）钻孔终孔质量检查验收报告书…………………… ………………………………14 附录 B （资料性附录）水文地质测绘质量验收书 …………………………………………………………20 附录 C （资料性附录）水文地质物探质量验收书 …………………………………………………………22 附录 D （资料性附录）动态观测质量验收书 ………………………………………………………………24
分类：安全管理制度 行业：建筑加工行业 文件类型：Word 文件大小：532 KB 时间：2026-01-05 价格：¥2.00
炊事机械日常点检表 点检月份： 年 月 编号： 设备名称 炊事机械 规格型号 设备编号 操作者 A 操作者 B 操作者 C 使用部门 检查日期 点检内容 点检记录 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 机械传动部位有完好可靠的防护装置 2 搅拌操作的容器必须加盖密闭且盖机联锁 3 PE 连接可靠，电源线路完好 4 每台设备应有单独的控制开关 5 凡有碾绞压挤切伤可能的部位均应有可靠防护 1 8 15 2 9 16 3 10 17 4 11 18 5 12 19 6 13 20 异 常 情 况 记 录 7 14 21 备 注 1.检查方法：看、听、试 2.检查周期：每天。（由车间负责人负责） 重大 安全 隐患 记录 注：保养后，用“√”表示进行了点检，“○”表示休息或放假， “×”表示有异常情况，应在“异常情况记录”栏予以记录。
分类：安全管理制度 行业：其它行业 文件类型：Word 文件大小：97 KB 时间：2026-02-17 价格：¥2.00